Skip to main content

Your #1 Arduino Datasheets Source

Search This Blog

Sitemap

Get link
Facebook
X
Pinterest
Email
Other Apps

Arduino Basics: Intro to The 74HC595 Shift Register - New !!
Downlad Arduino Uno Pinout Schematic Datasheet (PDF) - New !!
Download 74HC595 Arduino Datasheet | The 74HC595 Shift Register - New !!
Download ATmega328P Ardiuno Uno Datasheet (PDF) - New !!
Download Arduino ATmega2560 Datasheet (PDF) - New !!
Download Arduino ATmega328p Datasheet (PDF) - New !!
Download Arduino BME280 Sensor Manual Datasheet
Download Arduino DHT22 Sensor Datasheet (DHT22 also named as AM2302) - New !!
Download Arduino Uno R3 Datasheet (PDF) - New !!
Download Arduino Uno i2c Connection Datasheet (PDF)
Download DHT11 Datasheet (PDF) - Humidity & Temperature Sensor - New !!
Download DS18B20 Temperature Sensor Datasheet - New !!
Download SONOFF TH16 Temperature Sensor Manual Datasheet

Download CISCO Catalyst 3560 Datasheet (PDF)
Download CISCO Catalyst 3650 Datasheet (PDF)
Download CISCO Catalyst 3850 Switches Datasheet (PDF)
Download CISCO ISR 4331 Datasheet (PDF)
Download CISCO Nexus 9300 Switches Datasheet (PDF)
Download Cisco Catalyst 9300 Switch Datasheet (PDF)

Download Transistor NPN 2n2222A Datasheet (PDF)

Get link
Facebook
X
Pinterest
Email
Other Apps

Most Viewed Datasheets

Downlad Arduino Uno Pinout Schematic Datasheet (PDF)

arduino uno pinout datasheet pdf - The Arduino Uno is one of the most common and widely used Arduino processor boards. There are a wide variety of shields (plug in boards adding functionality). It is relatively inexpensive (about $25 -$35). Revision 2 added a pull-down resistor to the 8U2 HWB line, making it easier to put into DFU (Device Firmware Update) mode Revision 3 added: SDA and SCL pins are now brought out to the header near the AREF pin (upper left on picture). SDA and SCL are for the I2C interface IOREF pin (middle lower on picture that allows shields to adapt to the voltage provided Another pin not connected reserved for future use The board can be powered from the USB connector (usually up to 500ma for all electronics including shield), or from the2.1mm barrel jack using a separate power supply when you cannot connect the board to the PC’s USB port. Arduino Uno pinout – Power Supply There are 3 ways to power the Arduino Uno: Barrel Jack – The Barrel ...

Download Arduino Uno R3 Datasheet (PDF)

Arduino uno r3 datasheet pdf - Arduino is used for building different types of electronic circuits easily using of both a physical programmable circuit board usually microcontroller and piece of code running on computer with USB connection between the computer and Arduino. Programming language used in Arduino is just a simplified version of C++ that can easily replace thousands of wires with words. Arduino UNO-R3 Physical Components ATMEGA328P-PU Microcontroller The most important element in Arduino Uno R3 is ATMEGA328P-PU is an 8-bit icrocontroller with flash memory reach to 32k bytes. It’s features as follow: High Performance, Low Power AVR Advanced RISC Architecture 131 Powerful Instructions – Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Up to 20 MIPS Throughput at 20 MHz On-chip 2-cycle Multiplier High Endurance Non-volatile Memory Segments 4/8/16/32K Bytes of In-System Self-Programmable Flash program memory 256/512/512...

Download ATmega328P Ardiuno Uno Datasheet (PDF)

atmega328p ardiuno uno datasheet pdf - The Atmel ATmega328P is one member of the Atmel 8-bit microcontroller family. Each member ofthe family has different amounts of RAM, ROM, I/O ports, etc. Depending on the number of externalpins required they may come in packages with more than a hundred pins, or with as few as eight. The ATmega328P contains the following components: 32kb of FLASH memory for program storage. 2kb of RAM memory. 1kb of EEPROM memory Two 8-bit and one 16-bit timer/counters. These can count internal clock cycles or external events andgenerate an interrupt when reaching a specified count value. 6 channels of 10-bit analog-to-digital converter (ADC). Serial communications port. This can be used to communicate to the COM port of a computer. I2C interface port for communication with other I2C compatible ICs 21 lines of general purpose I/O. Not all of these functions are available at the same time. Most of ...

Home | About Us | Privacy Policy | Contact Us | Sitemap

Powered by Blogger

udatasheet - Your #1 Arduino Datasheet Source